Drywall Contractor & Drywall Repair in Waller, TX | Spring Drywall Co.
Spring Drywall Co. is a drywall contractor working in Waller, TX, and we have been doing this work for 15 years. Most of it is drywall repair and drywall installation. Drywall, gypsum board and Sheetrock are all names for the same panel, so sheetrock repair is the same work regardless of which term you use. We replace water-damaged board, remove old ceilings and popcorn texture, and handle finishing and texturing so the repaired area matches the surface around it. We also fit out commercial interiors.
The smaller jobs fall into three groups: specialty board for damp rooms or rated walls, new walls framed and boarded from the studs out, and the detail and surface work that leaves the room finished.
Waller sits 41 miles northwest of downtown Houston along U.S. Route 290. It is a city with its own limits, and those limits fall across two counties, Harris and Waller. The older houses here sit on large lots rather than in platted subdivisions.
We work across north Harris and Montgomery counties and west into Waller County, so Waller is inside that area rather than at the end of it. We are insured, the on-site estimate is free, the written estimate itemizes each part of the work before you commit, and financing is available on larger projects. Call (936) 286-6045 or use our quote form for a clear, written price on your project.
Why Choose Us
What Waller Property Owners Get From This Drywall Contractor
Hiring one contractor for the whole job makes the work simpler on a Waller property. Otherwise, you have to schedule a framer, hanger, taper and painter yourself, keep each trade lined up with the next, and sort out any problems between them. With one crew, the job stays with the same team from bare studs through to painted walls:
- building the metal stud framing that supports the walls
- hanging the board and finishing the seams between each sheet
- spraying the texture to match the surrounding surfaces
- priming and painting the finished wall
The same crew that starts your walls stays with the job through the final finish, so the room does not change hands partway through. Spring Drywall Co. also works as a drywall contractor in Magnolia, northeast of Waller. Call (936) 286-6045 or send your room measurements through our quote form, and we will come out to price the work.
Drywall Contractor Jobs We Cover in Waller
The same range of drywall work we do anywhere, we do in Waller. Some jobs stand on their own below and the rest are gathered under a single name.
Drywall Repair
Drywall repair is the refastening and patching of wall and ceiling board that has cracked, loosened or pulled apart at the seams. We refasten board that has pulled away from the studs, cut out and replace panels that are too damaged to hold, and retape the seam with drywall tape and joint compound. Nail pops, the small raised circles where a fastener has pushed through the surface, are repaired the same way.
Drywall Installation
Drywall installation is the hanging of new panels on bare framing and coating them into one flat surface. We hang and fasten the board to ASTM C840, which sets panel placement and fastening requirements, because loosely fixed board moves against the framing and leads to cracks and screw heads showing through your paint. We handle sheetrock installation in Waller houses and outbuildings, and we finish the board ourselves instead of leaving it hung for another trade to complete.
Water Damage Drywall Repair
Water damage drywall repair deals with soaked board, whether the water came through the roof during a Gulf storm, from a plumbing leak inside the wall, or from an attic air handler that dripped and stained the ceiling below it.
Board that has softened, swollen or separated into layers will not recover, so we remove it; board that only got damp and is still sound often dries in place. In either case, the framing behind it is dried before the wall is closed, and moisture- and mold-resistant board goes back in rooms that require it. We compare the exposed framing and surrounding materials against dry reference readings before closing the wall. Where Texas law requires licensed mold assessment or remediation, that work is handled by a licensed mold professional first.
Drywall Finishing & Texturing
Drywall finishing is the taping, coating and sanding that takes hung board to a surface ready for paint, while texture is the pattern applied over that finish. Most walls around here have orange peel or knockdown. Orange peel is a fine spatter, while knockdown starts with the same spatter and is then flattened with a blade. A smooth patch on a textured wall remains visible, so we match the texture already there. The Level 4 and Level 5 names come from GA-214, and the finish level is listed as its own line on your estimate. Because new paint does not match paint that has aged on the wall, the whole wall is often painted afterward.
Commercial Drywall
Commercial drywall is the same wall and ceiling work done inside a building people work or study in rather than live in. In Waller, that includes shop and office interiors as well as classroom and office space at Blinn College's Waller Workforce and Technical Education Complex. What changes is the calendar more than the board. We work Monday through Saturday, from eight in the morning to six in the evening, and schedule the work around the hours each room is available.
Ceilings & Popcorn Ceiling Removal
A ceiling is drywall too, hung overhead with its weight carried by the fasteners. We repair ceiling board that has sagged or stained, replace sections that are too damaged to keep, and install ceiling drywall in rooms that do not have it yet. We also scrape popcorn texture, the sprayed bumpy coating on older ceilings, back to a flat surface. Where a room needs better sound control, we install acoustical ceilings with panels that absorb sound instead of reflecting it back into the room. Popcorn texture or other suspect material is tested by a qualified asbestos professional when its age or condition warrants testing before disturbance, and we scrape only material the results clear as safe.
Drywall Types & Specialty Systems
Board comes in several grades, and the right one depends on the conditions in the room. We install moisture-resistant and mold-resistant drywall in bathrooms outside the shower, as well as in laundries and kitchens where the air is damp but the wall is not directly exposed to water. Ordinary gypsum drywall is outside our scope as the tile substrate in direct-wet shower and tub-surround zones. An approved tile-backer board goes behind the tile in those areas instead.
We build fire-rated drywall systems, where the rating comes from the complete tested assembly of board, framing and fasteners rather than from one sheet by itself. Soundproof drywall installation works on the same principle, with the sound control coming from the way the layers, framing and sealing are put together, which is the work we handle.
New Walls, From the Studs
New construction drywall is the first board installed in a room, hung on framing that has not been covered yet. We handle partition wall installation, building the interior walls that divide one space into two, and metal stud framing where steel studs are the better fit than wood. Insulation goes into the stud cavities before the board closes them, because getting back into a finished wall means opening it again. In Waller, that work is done just as often in an outbuilding or shop as it is in a house.
Detail and Surface Work
Some drywall work is about shaping and detailing rather than simply covering a wall. We build custom drywall and architectural features, including the curved, recessed and stepped forms a room is designed around, along with drywall soffits and bulkheads that box in ductwork and pipes above cabinets or along hallways. Corner bead installation and repair sets a metal or plastic strip on an outside corner so the strip takes the knocks instead of the board.
We also repair and finish existing surfaces, including plaster repair in older houses and wallpaper removal. Drywall that has pulled loose we rehang and reattach, and access panel installation puts a removable door where a valve has to stay reachable. We also handle drywall priming and painting. Primer makes the wall absorb paint evenly across patched and unpatched areas, and we paint the wall ourselves.
What Drywall Work Costs in Waller
These are starting ranges for the drywall repair costs most common in Waller, not a price for your own wall. Your price depends on the size of the repair, the finish, the access and how much board has to be removed.
- We patch a small to medium hole in the $200 to $600 range.
- We repair the drywall in one room in the $150 to $1,500 range.
- We repair a ceiling in the $400 to $1,300 range.
- We rebuild a wall after water damage in the $600 to $2,500 range.
- We hang, tape and finish new board to a Level 4 finish at $2.00 to $3.00 per square foot.
The number of rooms has the biggest effect on price. Masking, floor protection and sanding setup are done once and then carry across every room we work on during the same visit, so three rooms completed together cost less per room than three booked separately. Within each room, the size of the damaged area sets the rest of the cost because taping, coating and sanding all take longer over more board. We also prime and paint what we finish, so the price covers the wall through to a painted surface rather than stopping before that work is done.
Wall Repairs in Houses on Large Lots, Not Subdivisions
Older houses in Waller are generally one-story and set back on larger yards rather than platted subdivision lots, which affects how we plan the drywall repair and access the work area. We also finish interiors in workshops and other outbuildings, not just inside the house.
Carrying Drywall Board In From Where the Truck Stops
On a lot this size, the truck stops well short of the wall that needs work. Full sheets of board are then carried in by hand through a gate, across the yard and down the hallway to the room. We walk that route with you during the estimate so access is clear before the first sheet is moved.
That walk also shows us where the floor needs protection, since carrying board in from the yard brings grit along the route. We cover the full path before the work starts and remove the protection once the board is hung.
Drywall Cracks That Come Back on a Freestanding House
The ground here swells when it gets wet and shrinks as it dries, lifting and lowering the slab under a freestanding house a little with each season. Inside, that movement shows up as a hairline crack above a doorway or along a ceiling line that was filled before and has opened again in the same place. Filler alone does not hold because the joint underneath has already failed.
A sheetrock repair here starts by cutting back to board that is still sound and securely fastened. We re-tape the joint with drywall tape bedded in joint compound, build up the finish, and match the existing texture so the repair blends into the wall. If the movement is still active, a foundation specialist needs to assess it first, and we tell you that before any patching starts.
Drywall Contractor Work by Waller Neighborhood
Waller has two main types of areas for this work. The original center holds the city's older storefronts, while newer residential communities have been built inside the city limits north of U.S. Route 290. The materials we bring and the way we handle the job depend on which setting we are working in.
Downtown Waller: Finishing and Texturing in Renovated Storefronts
The city's oldest streets are downtown, where reinvestment has brought new businesses into buildings that were already standing. A tenant fitting out one of those spaces rarely starts with bare studs throughout, so new board has to meet wall surfaces that stay in place. We tape and coat the new work until it sits flush with the existing wall, then match the texture across both so your finished wall looks like one surface rather than a repair set into an older one.
Beacon Hill: Hanging Board on Houses Still Going Up
On the north side of U.S. Route 290, inside the city limits between FM 362 and James Muse Parkway, new houses are still being built. For us, what changes is that the date is set by somebody else: the board goes into a slot the builder has already fixed, and it has to be ready for whoever is booked after us. We hang full sheets on the studs, tape and coat the seams, and finish the surface to the level the next trade requires.
Oakwood Estates: Nail Pops and Seams in a Newly Built House
Oakwood Estates is an open community of recently built houses north of U.S. Route 290. A house that has stood only a year or two settles, and the walls show it: fasteners work out under the coating and leave the round bumps called nail pops, and hairline cracks open along the taped seams between sheets. In newer houses like these, both are common cosmetic repairs rather than structural problems. We reset the fastener, lay fresh tape and joint compound over the seam, and work the texture back so the repair disappears into the wall around it.
Attwater: Soundproof Drywall Between Rooms on a Narrower Lot
Lots in Attwater, off FM 362 and Owens Road, are narrower than those around many of the city's older houses, so rooms inside the home sit closer together. Where sound between a bedroom and living room, or through a shared wall, needs to be controlled, the work has to be built into the wall while it is open. We install soundproof drywall as part of that assembly, fastening it to the framing the same way as the rest of the board.
One Load, One Trip: Staging a Waller Drywall Job
Every Waller job is planned around the drive out U.S. Route 290. With a long trip each way, sending someone back for a forgotten box of screws takes time away from the work on your walls, so we prepare each visit to complete as much of the job as possible. That affects what we confirm before loading the truck and how we organize the work inside a house that is still occupied.
Why the Sheet Count Has to Be Right Before We Load
We measure your walls one at a time and use those measurements to plan the order of the work, the number of sheets and the length each sheet needs to be. A sheet that falls short does more than waste board; it creates another seam that has to be taped, coated and sanded, and every extra seam is another line that can show through the finish. We load corner bead, joint compound and texturing equipment from those same measurements because a little extra material costs a few dollars, while coming up short means another trip.
Dust Control in a House You Are Still Living In
Most houses here are occupied while we work, and sanding drywall creates fine dust that spreads into any room left open to the work area. Plastic barriers, sealed doorways, and vacuum-assisted sanding are part of the base scope on every occupied-space job, not an add-on. The sanding equipment pulls dust into a vacuum as it comes off the wall, before it settles on floors or furniture. We also plan the work into as few visits as possible, which means fewer days with rooms opened up and doorways sealed. We book by the day, Monday to Saturday, between eight in the morning and six in the evening.
Who Permits Drywall Work in Waller, City or County
A building permit for drywall work in Waller comes from the office responsible for the property's location. Inside the city limits, the city is the authority; outside them, the county is. That line on the map, and not the county your mail is addressed through, is what a drywall contractor has to establish before the work is priced.
Inside the Waller City Limits, the City Is the Authority
The City of Waller is incorporated, so it has its own government and issues building permits through its own office rather than through the county seat. Inside the city limits, the city is the authority for the job regardless of which county the property is in. A building permit belongs to the property and its owner, so it is issued in your name and we work within what it allows. Before work starts, we check with the City of Waller to confirm what your job requires instead of assuming no permit is needed.
Outside the City Limits: Harris County or Waller County
Waller's city limits cross the county line, with part of the city in Waller County and part in Harris County. Once a property falls outside those limits, the city is no longer the permitting authority and the job falls under one of the two counties instead. The mailing address does not determine which county office applies, and each county has its own authority, office and requirements. We confirm which one covers your address before quoting the work so the price reflects the job as it has to be done.
FAQ
Waller Drywall Questions, Answered
How should I get my house ready before you start?
Clear the room and remove anything hanging on the walls. Leave a path wide enough for us to carry full sheets of board into the work area, since access is the one part of the job we cannot bring with us. Tell us where the attic access and air handler are located so we can keep ceiling cuts clear of the unit and reach repairs from above where space allows. We bring the plastic barriers and sealing materials ourselves.
Can you do the whole job in one trip out to Waller?
Usually, yes. We work six days a week, which lets us give a Waller job a full working day. The exception is a finish that needs time to cure between coats, which requires a second visit. We tell you during the estimate whether your job will take one visit or two.
Which county is my Waller address in, and does it change who permits the work?
Your deed names either Harris County or Waller County, but inside the city limits that does not change who permits the work. The City of Waller is the authority whichever county the deed names. Outside the city limits, the county matters. If you are not sure which county covers the address, the county appraisal record will confirm it.
Do you schedule around the Waller ISD and Blinn College calendars?
Yes. In an occupied building, we schedule the work outside the hours the space is in use. Waller Independent School District and Blinn College's Waller complex each follow their own calendars, so we work around those dates rather than set them ourselves. Sealed doorways keep corridors and neighboring rooms usable while the work is underway, and we agree on access hours with the building before booking the job.
Do you actually come out to Waller, or stop closer to Spring?
Yes. Waller County is part of the territory we work, and this city is inside it rather than at its edge. We inspect the drywall repair in person before quoting instead of pricing from a photograph, so the estimate takes place at your property. Addresses outside the city limits are still within the area we cover.
Request Your Free Waller Drywall Estimate From Spring Drywall Co.
An estimate at your Waller address costs you nothing. We come out, measure the work in front of us, and provide a written price with each part of the job listed separately, including the finish level, so you can see exactly what you are paying for before you commit. On a larger project, financing lets you spread that cost over time rather than pay it in one sum. Call (936) 286-6045 or send your details through the quote form, and Spring Drywall Co. will arrange a day to come out and look.