Drywall Contractor & Drywall Repair in Porter, TX | Spring Drywall Co.
Spring Drywall Co. is a drywall contractor in Porter, Montgomery County, with 15 years behind us. We patch holes, cracks and failed seams as ordinary drywall repair, handle drywall installation when a new room is being built or a damaged wall needs to be replaced, and repair walls and ceilings after a roof leak or burst supply line. We also scrape popcorn ceilings, finish and texture new or repaired surfaces, do commercial drywall work, and prime and paint the drywall we install. Our hanging follows ASTM C840.
What decides the repair in Porter is when the house was built. The established sections inside ZIP code 77365 were finished decades before the newest ones, so the same crack can call for different work on two different streets. A wall built in one era does not behave the same way as a wall built in another.
Call (936) 286-6045 or use our quote form for a clear, written price on your project.
Why Choose Us
Hiring a Drywall Contractor in Porter: What You Get From Spring Drywall Co.
Most drywall work in Porter is done inside finished, occupied homes, so the repair has to blend into the surrounding wall or ceiling rather than simply end up flat and solid. One sheetrock contractor handles the full sequence, from framing and hanging through taping, texture, primer and paint.
Before we patch anything, we find out what caused the wall to get wet or crack in the first place, whether it is ground movement under the slab, a leak in a water line below the floor, condensate from an air conditioner, or water coming in through the roof. We check moisture by comparison, taking readings from material in the same building that we know is dry and comparing the suspect wall against those readings, because a meter reading by itself means different things in different houses.
Before we start work on your house, there are four things we make sure are settled, and each one is part of our standing policy.
- We carry general liability insurance and can send our certificate of insurance before work begins.
- Your on-site estimate is free.
- The written estimate is broken down by line item, so you can see the price of each part of the job before you commit.
- Financing is available for larger projects.
We also work in nearby Humble if you need a drywall contractor in Humble. To schedule an estimate in Porter, call (936) 286-6045.
Drywall Contractor Jobs We Cover in Porter
These are the wall and ceiling jobs we handle in Porter for houses, shops and campus buildings.
Drywall Repair
A sheetrock repair takes care of holes, popped nail heads, lifted seams and corner cracks above doors and windows in Porter. We cut a small hole square, add backing and patch it, while a soft or crumbling section gets cut back to the framing on both sides and replaced with a new piece. In either case, we screw the edges to solid framing, bed paper tape in joint compound over the joints, build the coats out beyond the repair, and match the existing texture before paint.
Drywall Installation
Drywall installation means putting new board over bare framing in an addition, a garage turned into a room, or a Porter house taken back to the studs. We follow ASTM C840, the standard for how gypsum panels are hung and fastened. Ceilings go up first, seams are staggered, and fastener heads are set just below the face. We then tape and finish the sheetrock installation to a named GA-214 level, usually Level 4, using 1/2-inch standard board.
Water Damage Drywall Repair
Water damage in Porter often reaches ceilings from above, especially from an attic air handler over finished rooms, but also from a roof leak or failed supply line. We remove the soaked board, dry the assembly behind it, and install new drywall, using mold-resistant board where the room calls for it. We compare the exposed framing and surrounding materials against dry reference readings before closing the wall. Where Texas law requires licensed mold assessment or remediation, that work is handled by a licensed mold professional first.
Drywall Finishing & Texturing
Finishing and texturing is what makes a new patch blend with the wall around it. On an older Porter wall, that means matching a texture that was sprayed years ago. On new board, we tape the seams, build the coats to the finish level named in your estimate, and sand between coats so the joints do not show through the paint.
Commercial Drywall
Commercial drywall work in Porter is mostly institutional rather than retail. We work on school campuses in the New Caney Independent School District, church halls, and small office and shop suites, often hanging board over steel framing. In an occupied building the room next door still has to work, so we seal off the work area, contain the dust, and stage materials out of the way. When a property manager needs the paperwork to match the building, we invoice each unit separately.
Ceilings & Popcorn Ceiling Removal
Ceiling work in Porter homes and buildings covers four main jobs: repairing or replacing damaged ceiling board, installing drywall on new or stripped framing, scraping popcorn texture and skimming the surface smooth, and installing acoustical ceilings with suspended grid and tile in offices and halls. Ceilings are also where leaks from attic air handlers show up first, so much of this work starts overhead. Popcorn texture or other suspect material is tested by a qualified asbestos professional when its age or condition warrants testing before disturbance, and we scrape only material the results clear as safe.
Drywall Types & Specialty Systems
Three types of board are used where ordinary gypsum board is not the right material. Moisture- and mold-resistant board is used in bathrooms outside the shower itself, as well as in laundry rooms and kitchens where humidity is high but water does not run directly over the surface. Ordinary gypsum drywall is outside our scope as the tile substrate in direct-wet shower and tub-surround zones; those areas require an approved tile-backer board, such as a cement-based panel made for direct exposure to water.
Fire-rated systems are the second type, and 5/8-inch Type X board is one part of that construction. The fire rating belongs to the full tested fire-rated assembly, including the framing, fasteners, layers and joints, so Type X board by itself does not make a wall fire rated. The third is soundproof drywall, where the sound control comes from the way the wall is built in layers, and our own crew handles that work from the framing out.
New Walls, From the Studs
Porter has plenty of existing buildings that need walls they were not originally built with. This work includes new construction drywall, partition wall installation, metal stud framing and insulation before drywall. Dividing a bedroom in a finished house, or building out the inside of a shop or office shell, starts with the framing: studs set between the floor and top plate, straight and plumb, before any board is hung. Cavity insulation goes in while the framing is still open, because once the drywall closes the cavity, getting back to it means cutting the wall open again.
Detail and Surface Work
Porter houses also have shaped and finished details that drywall has to meet. We build custom drywall and architectural features, including soffits and bulkheads, the boxed-in sections that lower a ceiling over cabinets or conceal ductwork. We also install and repair corner bead, the metal edge that protects an outside corner, and repair plaster in older houses where the walls were never board.
The rest is surface work. We remove wallpaper and repair any damage that comes away with it, handle primer and paint as part of our own finishing work, and rehang or reattach drywall that has pulled loose from the framing. Where a valve or junction box sits behind finished drywall, we install an access panel so it can be reached again without cutting the wall open.
What Drywall Work Costs in Porter
Drywall jobs in Porter fall into a few common types. These are market price ranges rather than quotes, and your on-site estimate sets the price for your own job.
- We patch a small to medium hole in the $200 to $600 range.
- We repair the drywall in one room in the $150 to $1,500 range.
- We repair a ceiling in the $400 to $1,300 range.
- We rebuild a wall after water damage in the $600 to $2,500 range.
- We hang, tape and finish new board to a Level 4 finish at $2.00 to $3.00 per square foot.
A drywall repair cost depends mostly on the texture we have to match. The original texture was not recorded when these houses were built, so we match what is already on the wall, and that work adds $150 to $350 by itself. A ceiling costs more than the same repair on a wall because every step is overhead, from lifting the board into place to sanding the final coat. The amount of board removed also affects the price, since more board means more taping, sanding and texture matching.
Porter's Established Subdivisions, and the Repairs They Need
A house in one of Porter's established sections, built roughly 20 to 50 years ago, needs different work from a newer house. We work in the newer sections too, but this is the work the older housing stock calls for. These homes are occupied, with finished floors and furniture still in place, so we seal off the room and keep sanding dust out of the rest of the house.
Two things make the work harder. There is no record of how these rooms were originally finished, and some of the damage comes from movement that is still active.
Matching a Finish Nobody Wrote Down
The texture on a wall of this age was sprayed on with a hopper and air, not spread by hand, so it has its own pattern. Orange peel texture is a fine spatter with a surface like orange skin, while knockdown texture starts with the same spatter and is flattened with a wide knife before it dries.
Neither the compound mix nor the air pressure used on your wall was recorded, so we spray test patches out of sight and adjust them until the pattern blends with the original. GA-214 sets the finish levels, and we work to the level already in the room: the standard finish used in most rooms, or a smoother finish skimmed across the full surface where gloss paint or low raking light would show every ridge. Fresh paint over a repair still reflects light differently from older paint, so on some walls the patch remains visible until the entire surface is coated.
Why the Same Seam Opens Every Year
Sheetrock repair in an older Porter house often comes down to the same two problems: a lifted joint where the ceiling meets the wall, and fastener pops, the small round bumps where a screw head has pushed through the surface. They come from two different kinds of movement, and identifying which one caused the damage determines how the repair is done so it holds.
Beaumont Clay, a highly expansive clay common in this part of the county, takes up water and releases it again, and over time that movement lifts and drops the concrete slab under the house. Truss uplift is different: the roof framing bows upward in winter and settles back in summer, opening a gap at the ceiling line and then closing it again. Because truss uplift reverses and ground movement does not, we identify the cause before closing the wall. If the movement is clearly still active, we will tell you to get a foundation opinion first, because patching before that means the same crack will open again.
Drywall Contractor Work by Porter Neighborhood
Porter housing varies by both age and size. Inside ZIP code 77365, some of the oldest and newest houses sit only a few minutes apart, and a wall in a late-1970s house on an acre lot needs different work from one in a three-thousand-square-foot custom house built last decade.
Oakhurst at Kingwood: Priming and Painting Around the Golf Course
This large planned community covers roughly 700 acres of fairways and cul-de-sacs. Its houses were built over about twenty-five years, from the 1990s until the last new homes sold in 2017, so the oldest walls are around thirty years old while the newest are under ten.
The older homes have usually been repainted more than once, and a fresh patch absorbs much more paint than the surrounding wall, which leaves the repair showing as a dull spot under the new color. We prime the patch and the wall around it first so the surface takes the finish coat evenly.
Timberlane Acres: Patching Plaster in the Oldest Houses in 77365
Houses here average around 1979 and sit on larger lots, with smaller floor plans than newer homes. Walls from that period are often not drywall at all. Plaster is applied wet in layers and left to harden, while a hard-coat surface is a thin cement-based layer over the wall, and both crumble rather than cut cleanly like board. Cut them like drywall and the damaged area spreads past where you wanted it. We identify the wall surface first and repair it with the method that matches what is already there.
Riverwalk: Custom Ceilings and Architectural Details in Large Houses
The houses on these wooded lots average around 3,000 square feet and were built one at a time rather than from a small set of plans. That is where more shaped drywall work shows up, including ceilings stepped up in tiers or sunk into paneled squares, arched openings, columns and recessed niches. Each of those details adds corners, and when a corner is framed out of square, movement in the structure concentrates along that line and the crack opens in the same place each year no matter how often it is filled. We rebuild the detail and its metal corner bead, not only the flat wall beside it.
Valley Ranch: Adding a Partition Wall Inside a Finished House
Valley Ranch is one of the newer planned sections, built with the wide open rooms that were common at the time. Those are the spaces owners now ask us to divide, usually to create a home office or fourth bedroom in a room that was never originally walled off. A partition wall is an interior wall that carries only its own weight, so we frame it with light metal studs rather than timber, hang the board, and finish it to the same smoothness as the walls around it so the new wall blends in with the room.
Auburn Trails at Oakhurst: Repairing Knocked Corners and Dropped Ceilings
This part of Porter sits next to the Oakhurst side of the community, and outside corners are the first part of a family home there to get damaged. Furniture, luggage and vacuum cleaners all hit them, and once the metal corner bead under the finish bends, it stays bent.
Above the kitchen cabinets, the same kind of damage happens for a different reason: the line where the underside of a bulkhead turns up into its face opens as the house settles. Filling over a crushed bead only covers the damage and leaves the corner weak, so we cut out the damaged bead and install a new length.
Getting a Drywall Crew and a Full Load to a Porter Address
A Porter job starts with the drive from the Spring side of north Harris County, heading east. The Eastex Freeway carries most of the route, so addresses near the older part of the community are a direct run. State Highway 99, the Grand Parkway, loops around the north side to reach properties farther from that older core, while Farm to Market Road 1314 takes us to houses on the Conroe side.
We are on those roads every week.
What Goes on the Truck Before We Drive Out
What goes on the truck is decided during the walk-through, before we load any board. We measure the rooms and make a materials list for the full job, including the drywall, metal corner bead, joint compound and paper tape for the seams, and the primer used at the end.
Board comes in 12-foot sheets, and a sheet that size has to make the turns and fit through the doorway into the room where it will be installed, so we check the access route during the walk-through. If a hallway is too tight for a full sheet, we load shorter board instead. Getting that right before we arrive helps keep a one-day job from turning into two days on site.
The Crew That Quotes the Job Is the Crew That Drives Out
The person who walks your property and prices the work is also the one running the crew that does it. The job is not handed from an estimator to a separate team that never saw the rooms, so the notes from that first visit stay with the people hanging the board. One accountable party carries the work from framing through paint, and if a question comes up on the second day, the answer does not depend on reaching someone back in north Harris County who has to be told what the walls look like. The same drywall contractor who stood in your hallway and quoted the job is the one making the drive back out to do it.
Montgomery County, Not Harris: Permitting a Porter Job
Porter is in unincorporated Montgomery County, so there is no city building department. Permit requirements are set by the county through the permitting division of its Environmental Health department. Because that office is not called a building department, someone searching for a Porter building department will not find one.
Which Jobs the County Wants to Hear About
The county's Development Permit applies to development, which it defines as a man-made change to real estate, including constructing buildings, grading, clearing, dredging and filling. Replacing drywall inside an existing room does not fall into those categories, while structural changes or breaking ground do. The county decides where a particular job falls, not us, so permit questions should be settled with them before work starts. We will tell you what we have seen on other Porter jobs.
FAQ
Porter Drywall Questions, Answered
Who issues permits for drywall work at a Porter address?
Montgomery County issues permits because Porter is unincorporated and does not have its own city building department. Your Municipal Utility District handles water and sewer billing, so it is not the office to call about permits, and neither is the school district. Permit questions on the county side go through Montgomery County Environmental Health.
My house is from the 1990s. Can you match the texture that is already on the wall?
Yes, and on a 1990s house that is the usual outcome. If the repaired area will not blend with the existing finish, the answer is a fresh coat across the entire wall or ceiling. We price that separately on the written estimate so you can decide whether to include it, instead of leaving you with a patch that still shows.
Can you schedule around the New Caney ISD school calendar?
Yes. Porter's campuses are part of New Caney Independent School District, so that calendar sets the schedule for work in those buildings. In a house, the main constraint is usually your family's school and work routine, so we schedule the loud, dusty stages for the hours the house is empty and leave the quieter work for when everyone is home.
We are out past the Grand Parkway. Is that still a normal job for you?
Yes, an address beyond State Highway 99 is part of our regular service area. We work Monday to Saturday, and for a property farther out, Saturday is often the easiest day to schedule because we can give the full day to one house instead of splitting it between two jobs.
Do you cover all of Porter, or only the parts near Kingwood?
We cover all of Porter, not just the part closest to our side of the service area. A single-room repair at the far edge of Porter is as routine for a drywall contractor as a whole-house job, and we will come out for a single hole. Whatever the Porter address, the answer is the same.
Request Your Free Porter Drywall Estimate From Spring Drywall Co.
An estimate starts with someone standing in front of the wall. We come to your Porter property, inspect the damage in person rather than relying on a photograph, and write up what we find as a line-itemed scope for you to review before you agree to anything. The visit is free, and financing is available on larger projects. Call (936) 286-6045 or send the details through our quote form, and Spring Drywall Co. will arrange a time to come out and look.